The SEQTEST procedure displays the “Design Information” and “Test Information” tables by default.
The “Conditional Power Information” table displays the following information under a hypothetical reference:
stopping stage
MLE, observed maximum likelihood estimate
conditional power under the hypothetical reference
For a onesided test, the power are derived under hypothetical references and , where is the observed statistic, is the alternative reference, and are the values specified in the CREF= option. For a twosided test, the power are derived under the hypothetical references , , and , where is the lower alternative reference and is the upper alternative reference. The default is CREF= 0 0.5 1.0 1.5.
The “Design Information” table displays the design specifications and derived statistics. The derived Max Information (Percent FixedSample) is the maximum information for the sequential design in percentage of the corresponding fixedsample information.
The Null Ref ASN (Percent FixedSample) is the average sample size required under the null hypothesis for the group sequential design in percentage of the corresponding fixedsample design. Similarly, the Alt Ref ASN (Percent FixedSample) is the average sample size required under the alternative reference for the group sequential design in percentage of the corresponding fixedsample design.
The “Error Spending Information” table displays the following information at each stage:
proportion of information
actual information level, if the maximum information is either specified or derived
cumulative error spending for each boundary
The “Parameter Estimates” table displays the following information at the conclusion of a sequential trial:
stopping stage
parameter estimate
median and confidence limits based on the specified ordering
pvalue for the hypothesis based on the specified ordering
The “Powers and Expected Sample Sizes” table displays the following information under each of the specified hypothetical references , where is the alternative reference and are values specified in the CREF= option.
coefficient for the hypothetical references. The value corresponds to the null hypothesis and corresponds to the alternative hypothesis
power
expected sample size, as percentage of fixedsample size
For a onesided design, the power and expected sample sizes under the hypothetical references are displayed.
For a twosided symmetric design, the power and expected sample sizes under each of the hypothetical references are displayed, where is the upper alternative reference.
For a twosided asymmetric design, the power and expected sample sizes under each of the hypothetical references and are displayed, where and are the lower and upper alternative references, respectively.
For a twosided design, the power is the probability of correctly rejecting the null hypothesis for the correct alternative. Thus, under the null hypothesis, the displayed power corresponds to a onesided Type I error probability level—that is, the lower level or the upper level.
The expected sample size as a percentage of the corresponding fixedsample design is

where is the stopping probability at stage k, is the expected information level, and is the information level for the fixedsample design.
The “Predictive Power Information” table displays the following information:
stopping stage
MLE, observed maximum likelihood estimate
predictive power
The “Repeated Confidence Intervals” table displays the following information for the observed statistic at each stage:
information level
parameter estimate
rejection confidence limits. The null hypothesis is rejected for the upper alternative if the lower rejection confidence limit is greater than the null parameter value. Similarly, the null hypothesis is rejected for the lower alternative if the upper rejection confidence limit is less than the null parameter value.
acceptance confidence limits. The upper alternative hypothesis is rejected if the upper acceptance confidence limit is less than the upper alternative value. Similarly, the lower alternative hypothesis is rejected if the lower acceptance confidence limit is greater than the upper alternative value. For a twosided design, if both upper and lower alternative hypothesis are rejected, the null hypothesis is accepted.
The “Expected Cumulative Stopping Probabilities” table displays the following information under each of the specified hypothetical references , where are values specified in the CREF= option, and is the alternative reference:
coefficient for the hypothetical references. The value corresponds to the null hypothesis, and corresponds to the alternative hypothesis
expected stopping stage
source of the stopping probability: reject (with STOP=REJECT or STOP=BOTH), accept (with STOP=ACCEPT or STOP=BOTH), or either reject or accept (with STOP=BOTH)
expected cumulative stopping probabilities at each stage
For a onesided design, the expected cumulative stopping probabilities under the hypothetical references are displayed.
For a twosided design, the expected cumulative stopping probabilities under each of the hypothetical references and are displayed, where and are the lower and upper alternative references, respectively.
Note that for a symmetric twosided design, only the expected cumulative stopping probabilities under the hypothetical references are derived.
The expected stopping stage is given by and is derived from the expected information level

where is the stopping probability at stage k and .
For equally spaced information levels, the expected stopping stage is reduced to the weighted average

The “Test Information” table displays the following information at each stage:
proportion of information
actual information level, if the maximum information is available from the input BOUNDARY= data set
alternative references with the specified statistic scale. If a pvalue scale is specified, the standardized Z scale is used.
boundary values with the specified statistic scale to reject or accept the null hypothesis
Note that implicitly, the test information table also contains variables for the boundary scale, stopping criterion, and type
of alternative hypothesis. That is, if an ODS statement is used to save the table, the data set also contains the variables
_Scale_
for the boundary scale, _Stop_
for the stopping criterion, and _ALT_
for the type of alternative hypothesis.
If the test variable is specified, the table also displays the following:
test statistic
resulting action of test statistic: continue to the next stage, accept the null hypothesis , or reject