XCHART Statement: SHEWHART Procedure

Note: See Mean (X-BAR) Chart Examples in the SAS/QC Sample Library.

The previous example illustrates how you can create charts using raw data (process measurements). However, in many applications, the data are provided as subgroup summary statistics. This example illustrates how you can use the XCHART statement with data of this type.

The following data set (Parts) provides the data from the preceding example in summarized form:

data Parts;
   input Sample PartgapX PartgapR;
   PartgapN=5;
   label PartgapX='Mean of Gap Width'
         Sample  ='Sample Index';
   datalines;
 1  270  35
 2  258  25
 3  248  24
 4  260  39
 5  273  29
 6  260  21
 7  259  37
 8  248  37
 9  260  28
10  255  19
11  268  36
12  253  36
13  273  29
14  275  22
15  257  24
16  269  41
17  249  36
18  264  31
19  258  25
20  248  36
21  248  30
;

A partial listing of Parts is shown in Figure 18.98. There is exactly one observation for each subgroup (note that the subgroups are still indexed by Sample). The variable PartgapX contains the subgroup means, the variable PartgapR contains the subgroup ranges, and the variable PartgapN contains the subgroup sample sizes (these are all five).

You can read this data set by specifying it as a HISTORY= data set in the PROC SHEWHART statement, as follows:

options nogstyle;
goptions ftext='albany amt';
title 'Mean Chart for Gap Width';
proc shewhart history=Parts;
   xchart Partgap*Sample / cframe   = vigb
                           cinfill  = vlib
                           cconnect = red;
run;
options gstyle;

The NOGSTYLE system option causes ODS styles not to affect traditional graphics. Instead, the XCHART statement options control the appearance of the graph. The GSTYLE system option restores the use of ODS styles for traditional graphics produced subsequently. The resulting chart is shown in Figure 18.99.

Note that Partgap is not the name of a SAS variable in the data set but is, instead, the common prefix for the names of the three SAS variables PartgapX, PartgapR, and PartgapN. The suffix characters X, R, and N indicate mean, range, and sample size, respectively. Thus, you can specify three subgroup summary variables in a HISTORY= data set with a single name (Partgap), which is referred to as the process. The name Sample specified after the asterisk is the name of the subgroup-variable.

Figure 18.99: Chart from the Summary Data Set Parts (Traditional Graphics with NOGSTYLE)

In general, a HISTORY= input data set used with the XCHART statement must contain the following variables:

Furthermore, the names of the subgroup mean, range (or standard deviation), and sample size variables must begin with the process name specified in the XCHART statement and end with the special suffix characters X, R (or S), and N, respectively. If the names do not follow this convention, you can use the RENAME option in the PROC SHEWHART statement to rename the variables for the duration of the SHEWHART procedure step (see Creating Charts for Means and Ranges from Summary Data).

If you specify the STDDEVIATIONS option in the XCHART statement, the HISTORY= data set must contain a subgroup standard deviation variable; otherwise, the HISTORY= data set must contain a subgroup range variable. The STDDEVIATIONS option specifies that the estimate of the process standard deviation is to be calculated from subgroup standard deviations rather than subgroup ranges. For example, in the following statements, the data set Parts2 must contain a subgroup standard deviation variable named PartgapS:

title 'Mean Chart for Gap Width';
proc shewhart history=Parts2;
   xchart Partgap*Sample='*' / stddeviations;
run;

Options such as STDDEVIATIONS are specified after the slash (/) in the XCHART statement. A complete list of options is presented in the section Syntax: XCHART Statement.

In summary, the interpretation of process depends on the input data set.

For more information, see HISTORY= Data Set.