The REG Procedure

Consider a response variable Y that can be predicted by a polynomial function of a regressor variable X. You can estimate , the intercept; , the slope due to X; and , the slope due to , in

for the observations .

Consider the following example on population growth trends. The population of the United States from 1790 to 2000 is fit to linear and quadratic functions of time. Note that the quadratic term, YearSq, is created in the DATA step; this is done since polynomial effects such as Year*Year cannot be specified in the MODEL statement in PROC REG. The data are as follows:

data USPopulation;
   input Population @@;
   retain Year 1780;
   Year       = Year+10;
   YearSq     = Year*Year;
   Population = Population/1000;
   datalines;
3929 5308 7239 9638 12866 17069 23191 31443 39818 50155
62947 75994 91972 105710 122775 131669 151325 179323 203211
226542 248710 281422
;

proc reg data=USPopulation plots=ResidualByPredicted;
   var YearSq;
   model Population=Year / r clm cli;
run;

The DATA option ensures that the procedure uses the intended data set. Any variable that you might add to the model but that is not included in the first MODEL statement must appear in the VAR statement.

The "Analysis of Variance" and "Parameter Estimates" tables are displayed in Figure 85.5.

The Model F statistic is significant (F = 228.92, p < 0.0001), indicating that the model accounts for a significant portion of variation in the data. The R-square indicates that the model accounts for 92% of the variation in population growth. The fitted equation for this model is

In the MODEL statement, three options are specified: R requests a residual analysis to be performed, CLI requests 95% confidence limits for an individual value, and CLM requests these limits for the expected value of the dependent variable. You can request specific % limits with the ALPHA= option in the PROC REG or MODEL statement.

Figure 85.6 shows the "Output Statistics" table. The residual, its standard error, the studentized residual, and Cook’s D are displayed for each observation. The studentized residual is the residual divided by its standard error. Cook’s D is a measure of the change in the predicted values upon deletion of that observation from the data set; hence, it measures the influence of the observation on the estimated regression coefficients. The studentized residuals and Cook’s D statistics are displayed in Figure 85.7.

Studentized residuals follow a beta distribution and can be used to identify outlying or extreme observations:

Figure 85.7: Studentized Residuals

Figure 85.8 shows the residual statistics table. A fairly close agreement between the PRESS statistic (see Table 85.7) and the sum of squared residuals indicates that the MSE is a reasonable measure of the predictive accuracy of the fitted model (Neter, Wasserman, and Kutner, 1990).

Graphical representations are very helpful in interpreting the information in the "Output Statistics" table. When ODS Graphics is enabled, the REG procedure produces a default set of diagnostic plots that are appropriate for the requested analysis.

Figure 85.9 displays a panel of diagnostics plots. These diagnostics indicate an inadequate model:

Figure 85.9: Diagnostics Panel

Figure 85.10 shows a plot of residuals versus Year. Again you can see the quadratic pattern that strongly indicates that a quadratic term should be added to the model.

Figure 85.10: Residual Plot

Figure 85.11 shows the FitPlot consisting of a scatter plot of the data overlaid with the regression line, and 95% confidence and prediction limits. Note that this plot also indicates that the model fails to capture the quadratic nature of the data. This plot is produced for models containing a single regressor. You can use the ALPHA= option in the model statement to change the significance level of the confidence band and prediction limits.

Figure 85.11: Fit Plot

These default plots provide strong evidence that the Yearsq needs to be added to the model. You can use the interactive feature of PROC REG to do this by specifying the following statements:

   add YearSq;
   print;
run;

The ADD statement requests that YearSq be added to the model, and the PRINT command causes the model to be refit and displays the ANOVA and parameter estimates for the new model. The print statement also produces updated ODS graphical displays.

Figure 85.12 displays the ANOVA table and parameter estimates for the new model.

The overall F statistic is still significant (F = 8864.19, p < 0.0001). The R-square has increased from 0.9197 to 0.9989, indicating that the model now accounts for 99.9% of the variation in Population. All effects are significant with p < 0.0001 for each effect in the model.

The fitted equation is now

Figure 85.13 show the panel of diagnostics for this quadratic polynomial model. These diagnostics indicate that this model is considerably more successful than the corresponding linear model:

Figure 85.13: Diagnostics Panel

When a model contains more than one regressor, PROC REG does not produce a fit plot. However, when all the regressors in the model are functions of a single variable, it is appropriate to plot predictions and residuals as a function of that variable. You request such plots by using the PLOTS=PREDICTIONS option in the PROC REG statement, as the following code illustrates:

proc reg data=USPopulation plots=predictions(X=Year);
   model Population=Year Yearsq;
quit;

ods graphics off;

Figure 85.14 shows the data, predictions, and residuals by Year. These plots confirm that the quadratic polynomial model successfully model the growth in U.S. population between the years 1780 and 2000.

Figure 85.14: Predictions and Residuals by Year

To complete an analysis of these data, you might want to examine influence statistics and, since the data are essentially time series data, examine the Durbin-Watson statistic.