The MVPMODEL Procedure

Relationship of Principal Components to Multivariate Control Charts

Subsections:

Multivariate control charts typically plot the $T^2$ statistic, which is a summary of multivariate variation. The classical $T^2$ statistic is defined in Classical T-Square Charts. When there is high correlation among the process variables, the correlation matrix is nearly singular. The subspace in which the process varies can be adequately explained by fewer variables than the original p variables. Thus, the principal component approach to multivariate control charts is to project the original p variables into a lower-dimensional subspace by using a model based on j principal components, where $j<p$.

The key to the relationship between principal components and multivariate control charts is the decomposition of the sample covariance matrix, $\bS $, into the form $\bS = \bP \bL \bP ^{\prime }$, where $\bL $ is a diagonal matrix (Jackson 1991; Mardia, Kent, and Bibby 1979). This is also the eigenvalue decomposition of $\bS $, where the columns of $\bP $ are the eigenvectors and the diagonal elements of $\bL $ are the eigenvalues.

Equivalence of $T^2$ Statistics

The $T^2$ statistic that is produced by the full principal component model is equivalent to the classical $T^2$ statistic. This is seen in the matrix representation of the $T^2$ statistic computed from a principal component model that uses all p components,

\[ T^2_ i = \left(\mb{t}_ i - \bar{\mb{t}}_ n \right)^{\prime } \mb{L}^{-1}_ n \left(\mb{t}_ i - \bar{\mb{t}}_ n \right) \]

Because $\bar{\mb{t}}_ n$ is the zero matrix by construction, then

\[ T^2_ i = \mb{t}_ i^{\prime } \mb{L}^{-1}_ n \mb{t}_ i \]

Because $\mb{t}_ i=\bP ^{\prime } \left( \mb{x}_ i- \bar{ \mb{x} } \right)$, then

\[ \begin{array}{rl} T^2_ i & = \mb{t}_ i^{\prime } \mb{L}^{-1}_ n \mb{t}_ i \\ & = \left( \bP ^{\prime } \left( \mb{x_ i}- \bar{ \mb{x} } \right) \right)^{\prime } \mb{L}^{-1}_ n \left( \bP ^{\prime } \left( \mb{x_ i}- \bar{\mb{x} } \right) \right) \\ & = \left( \mb{x}_ i- \bar{ \mb{x} } \right)^{\prime } \mb{P} \mb{L}^{-1}_ n \mb{P}^{\prime } \left( \mb{x}_ i - \bar{ \mb{x} } \right) \\ & = \left( \mb{x}_ i- \bar{ \mb{x} } \right)^{\prime } \bS ^{-1} \left( \mb{x}_ i- \bar{ \mb{x} } \right) \end{array} \]

which is the classical form. Consequently the classical $T^2$ statistic can be expressed as a sum of squares,

\[ T^2_ i = \frac{t^2_{i1}}{l^2_{1}} + \ldots + \frac{t^2_{ip}}{l^2_{p}} \]

where $l^2_{k}$ is the variance of the kth principal component.

Computing the $T^2$ and SPE Statistics

Creating a $T^2$ chart that is based on a principal component model begins with choosing the number (j) of principal components. Effectively, this involves selecting a subspace in $j<p$ dimensions and then creating a $T^2$ statistic based on that j-component model.

The $T^2$ statistic is meant to monitor variation in the model space. However, if variation appears in the $p-j$ subspace orthogonal to model space, then the model assumptions and physical process should be reexamined. Variation outside the model space can be detected with an SPE chart.

In a model with j principal components, the $T^2$ statistic is calculated as

\[ T^2_ i = \frac{t^2_{i1}}{l^2_{1}} + \ldots + \frac{t^2_{ij}}{l^2_{j}} \]

where $t_{ik}$ is the principal component score for the kth principal component of the ith observation and $l_{k}$ is the standard deviation of $t_{ik}$.

The information in the remaining $p-j$ principal components is monitored with charts for the SPE statistic, which is calculated as

\[ \begin{array}{rl} \mr{SPE}_ i & = \sum _{k=j+1}^{p} e^2_{ik} \\ & = \sum _{k=j+1}^{p} \left( x_{ik} - \hat{x}_{ik} \right)^2 \\ \end{array} \]