XRCHART Statement: SHEWHART Procedure
The values of the subgroup-variable, which is specified in the chart statement, indicate how the observations in the input data set (a DATA=, HISTORY=, or TABLE= data set) are arranged into rational subgroups.[36] Typically, the values of the subgroup-variable are one of the following:
-
indices that give the order in which subgroup samples were collected (for example, 1, 2, 3, . . . ). An unformatted numeric subgroup-variable is appropriate for this situation. For an example that uses this type of subgroup-variable, see Creating Charts for Means and Ranges from Raw Data.
-
the dates or times at which subgroup samples were collected (for example, 01JUN, 02JUN, 03JUN, . . . ). A numeric subgroup-variable with a SAS date, time, or datetime format is appropriate for this situation. You can optionally associate a format with the subgroup-variable by using a FORMAT statement; refer to SAS Formats and Informats: Reference for details. For an example that uses this type of subgroup-variable, see Example 17.40.
-
labels that uniquely identify subgroup samples (for example, LOT39, LOTX12, LOT43A). A character subgroup-variable (with or without a format) is appropriate for this situation. For an example that uses this type of subgroup-variable, see Example 17.38.
The values of the subgroup-variable also determine how the horizontal axis of the control chart is scaled and labeled.
The notion of a rational subgroup is fundamental to the application of a Shewhart chart. You should select your subgroups so that if special causes of variation are present, the opportunity for variation within subgroups is minimized while the opportunity for variation between subgroups is maximized. In other words, the conditions within a subgroup should be homogeneous. The reason for this requirement is that the construction of the control limits is based on within-subgroup variability. Refer to Montgomery (1996) and Wheeler and Chambers (1986) for approaches to rational subgrouping.
The selection of subgroups is both a practical and a statistical issue that requires knowledge of the process and the sampling or measurement procedure. The values of the subgroup-variable should reflect the selection of subgroups and should not be assigned arbitrarily. Incorrect subgrouping or assignment of subgroup-variable values can result in control limits that are too tight or too wide.
If the input data set is a HISTORY= or TABLE= data set, each observation represents a distinct subgroup, and, consequently, the observations within each BY group must have distinct subgroup variable values. Similarly, if the input data set is a DATA= data set and you are using the CCHART, IRCHART, NPCHART, PCHART, or UCHART statement, each observation represents a distinct subgroup, and, consequently, the observations within each BY group must have distinct subgroup variable values. However, if the input data set is a DATA= data set and you are using the BOXCHART, MCHART, MRCHART, RCHART, SCHART, XCHART, XRCHART, or XSCHART statement, subgroups are identified by groups of consecutive observations with identical values of the subgroup-variable.
The order of the observations in the input data set and the scaling of the horizontal axis depend on the type of the subgroup-variable, which can be numeric or character.
If the subgroup-variable is numeric, the observations must be sorted in increasing order of the values of the subgroup variable. If you use a BY statement, first sort by the BY variables and then by the subgroup variable.
The unformatted values of the subgroup-variable are used to scale the horizontal axis of the control chart, and the formatted values are used to label the major tick marks on the horizontal axis. As a result, the horizontal distance between two points corresponding to consecutive subgroups is proportional to the difference between their unformatted subgroup values.
If a DATE, DATETIME, WEEKDATE, or WORDDATE format is associated with the subgroup variable, the major tick mark labels are split and displayed in two levels to save space. You can override this default with the TURNHLABELS option (which turns the labels vertically) or with tick label options in an AXISn statement specified with the HAXIS= option.
If the subgroup-variable is numeric, the order of the observations is not checked. The horizontal axis is scaled so that the subgroups are spaced uniformly. Formatted subgroup variable values are used to label the major tick marks.
You can use a character subgroup variable to avoid gaps between groups of points or time values on a control chart. You can also use a character subgroup variable to create a chart in which the order of the points depends only on the order in which the subgroups are arranged in the input data set.
You should verify the order of the observations in the input data set before you use a character subgroup variable in conjunction with the TESTS= option. With the exception of Test 1, the tests for special causes are applicable only if the subgroups are provided in chronological order. See Tests for Special Causes: SHEWHART Procedure for details.
To avoid collision of adjacent tick labels on the horizontal axis, the labels are thinned by default. You can override this default with the TURNHLABELS option or with tick label options in an AXISn statement specified with the HAXIS= option.
[36] This discussion also applies to the use of subgroup-variables in the CUSUM procedure and the MACONTROL procedure.