Create and Start the Default Service

You must create a default Application Dispatcher service to run any of the sample programs supplied with SAS/IntrNet. Before you create the service, you must reserve a TCP/IP port number for your default Application Dispatcher service. Consult your system administrator or check your services definition file to find an available port number.

You should create the default service with the SAS/IntrNet Configuration Utility (inetcfg). This utility is available for

Windows platforms
UNIX platforms
z/OS
OpenVMS.

After you create and start the service, continue with Adding the Default Service Definition to the Application Broker configuration file.

Windows Platforms

Services can be created on Windows platforms with a configuration utility that is accessible from the Start menu.

Perform the following steps to create and start the default service:

From the Start menu, select Programs SAS (or other program group where SAS is installed) IntrNet Create a New IntrNet Service.
The IntrNet Config Utility Welcome window appears.
Read the information in the Welcome window, and then select Next to continue.
Select Create a Socket Service, then select Next to continue.
Type default as the name of the new service. Select Next to continue.
Specify the directory where you want the configuration utility to place your service directory and control files. The default location (under your SASUSER directory) is recommended. Select Next to continue.
Type the TCP/IP port number that you reserved for the default Application Dispatcher service. Select Next to continue.
A password is not necessary for the default service. You can add an administrator password later if you use this service for production applications. Select Next to continue.
The Create Service window displays all of the information that you specified for this service. Verify that the information is correct and then select Next to create the service.
Select Next and then Finish to complete the setup of the default service.
From the Start menu, select Programs SAS (or other program group where SAS is installed) IntrNet default Service Start Interactively. Your default Application Server should now be running.

UNIX Platforms

On UNIX platforms, the configuration utility is a Perl script. Perform the following steps to create and start the default service:

From a system prompt, submit the following command:
```
   SASROOT/utilities/bin/inetcfg.pl
```
where SASROOT is the path to the SAS root directory.

As the configuration utility runs, you are prompted for information about the service that you are creating.
Press Return to accept the default value, which names the service default.
The next prompt asks for the name of the directory where all of the service control files should be stored. Press Return to accept the suggested value, or type the desired directory name and then press Return.
Type S and press Return to define a socket service.
Press Return to select one server.
Type the TCP/IP port number that you reserved for this service and press Return.
Press Return to skip entering an administrator password. You can add an administrator password later if you use this service for production applications.
Verify the displayed information and press Return to create the service. Note the path for the service directory.
The configuration utility created a start.pl file to start the default Application Server. Change to the service directory path and start the server by submitting the following command:
```
   ./start.pl
```

z/OS

The configuration utility provided for z/OS is a batch job. It is installed as a member named INETCFG in the CNTL data set that you created as the first step in the installation of your SAS software. To use the utility, you must edit the parameter file, member INETEDTP in the CNTL data set, edit the INETCFG job, and then submit the INETCFG job. The INETEDTP member contains the parameters necessary for creating a service.

To create and start the default service on z/OS, perform the following steps:

Edit the member INETEDTP.
Verify the name of the service that you are creating. The service name is defined by the line beginning with ISVC= and should be DEFAULT.
Verify that the service is a socket service. The line containing ISVCTYP=%SOCKETTYP should be uncommented.
Locate the line I$-PORT1. Change the value 5001 to the correct port number or network service name for your Application Server.
Save and close INETEDTP.
Edit INETCFG to verify the job header information. Verify that the service name is DEFAULT. If you make changes, be sure to save them. Do NOT change SASEDITP to INETEDTP because this is your original SAS installation parameters file.
Submit the INETCFG JCL job for processing. The INETCFG job will submit another job (INETCFGA). Verify that both jobs completed with a return code of 0. If they completed successfully, you now have the data sets and members necessary for running the default service.
If the INETCFG job failed, examine the messages and sysprint members for error messages. If you see a message that reads
```
   ERROR: THIS REPLACEMENT CAUSES RESULT TO EXCEED OUTPUT LRECL
```
you might have supplied a pathname in one of your INETEDTP parameters that is too long. Try shortening this pathname and rerun INETCFG.

Note: Before you run INETCFG again, you must delete any data sets created by the previous failure of INETCFG. You can find these data sets by looking in the namespace determined by your original SAS install. For example, if your SAS software was installed with the prefix name SYS.SAS and your failed INETCFG was trying to create the DEFAULT service, then delete all data sets beginning with the name prefix SYS.SAS.WEB.DEFAULT before running INETCFG again.
The configuration utility creates a server root in a partitioned data set (PDS) named prefix.WEB.DEFAULT, where prefix is the data set prefix that you supplied during your SAS installation. The PDS contains any JCL procedures and server start-up code required for starting the service. You will find the following members:

APSTRT1

contains the JCL necessary to run the corresponding @APSTX1 file as a started task. You should move this file to your started task library and enable it as a started task.

@APSTX1

contains the SAS code that invokes the server. This file is called by the JCL in the corresponding APSTRT1 file. This SAS program must remain in the PDS where it was created.

In addition to the server root PDS, the configuration utility creates an empty PDS named prefix.WEB.DEFAULT.TDIR, where prefix is the data set prefix that you supplied during your SAS installation. The Application Server will use this PDS as a scratch location.
You must modify the permissions for the data sets created above so that the server can write to them as necessary. To modify the permissions, create a special RACF data set profile that applies to all the data sets in this service (prefix.WEB.DEFAULT.*). The RACF data set profile should also grant write access to the user ID of the Application Server.
Issue a START command from the system console to start the default Application Server.

OpenVMS

To create and start the default service on OpenVMS, perform the following steps:

From a system prompt, submit @sas$root:[tools]inetcfg.com.
As the configuration utility runs, you are prompted for information about the service that you are creating.
Press Return to name the service DEFAULT.
Press Return to accept the suggested value for the server root directory.
Type S to define a socket service. Press Return to continue.
Press Return to select one server for this service.
Type the TCP/IP port number or name that you reserved for the default Application Server and press Return.
A password is not necessary for the default service. You can add an administrator password later if you use this service for production applications. Press Return to continue.
The utility displays the information that you entered for this service. Verify that the information is correct. If the information is correct, press Return to create the service. Read the messages to determine if the service was created correctly. One of these messages contains the path for the service directory created by the utility. You should note this path for use later in this process.
The configuration utility created a START.COM file that starts the default Application Server. To start the server, change to the service directory created by the utility. Then submit the following command:
```
   @START.COM
```