Before using PROC FASTCLUS, decide whether your variables should be standardized in some way, since variables with large variances tend to have more effect on the resulting clusters than those with small variances. If all variables are measured in the same units, standardization might not be necessary. Otherwise, some form of standardization is strongly recommended. The STDIZE procedure provides a variety of standardization methods, including robust scale estimators (for detailed information, see ChapterÂ 94: The STDIZE Procedure).

The FACTOR or PRINCOMP procedure can compute standardized principal component scores. The ACECLUS procedure can transform the variables according to an estimated within-cluster covariance matrix.

Nonlinear transformations of the variables can change the number of population clusters and should therefore be approached with caution. For most applications, the variables should be transformed so that equal differences are of equal practical importance. An interval scale of measurement is required. Ordinal or ranked data are generally not appropriate.

PROC FASTCLUS produces relatively little output. In most cases you should create an output data set and use another procedure such as PRINT, SGPLOT, MEANS, DISCRIM, or CANDISC to study the clusters. It is usually desirable to try several values of the MAXCLUSTERS= option. Macros are useful for running PROC FASTCLUS repeatedly with other procedures.

A simple application of PROC FASTCLUS with two variables to examine the 2- and 3-cluster solutions can proceed as follows:

proc stdize method=std out=stan; var v1 v2; run; proc fastclus data=stan out=clust maxclusters=2; var v1 v2; run; proc sgplot; scatter y=v2 x=v1 / markerchar=cluster; run; proc fastclus data=stan out=clust maxclusters=3; var v1 v2; run; proc sgplot; scatter y=v2 x=v1 / markerchar=cluster; run;

If you have more than two variables, you can use the CANDISC procedure to compute canonical variables for plotting the clusters. For example:

proc stdize method=std out=stan; var v1-v10; run; proc fastclus data=stan out=clust maxclusters=3; var v1-v10; run; proc candisc out=can; var v1-v10; class cluster; run; proc sgplot; scatter y=can2 x=can1 / markerchar=cluster; run;

If the data set is not too large, it might also be helpful to use the following to list the clusters:

proc sort; by cluster distance; run; proc print; by cluster; run;

By examining the values of `DISTANCE`

, you can determine if any observations are unusually far from their cluster seeds.

It is often advisable, especially if the data set is large or contains outliers, to make a preliminary PROC FASTCLUS run with
a large number of clusters, perhaps 20 to 100. Use MAXITER=0 and OUTSEED=*SAS-data-set*. You can save time on subsequent runs if you select cluster seeds from this output data set by using the SEED= option.

You should check the preliminary clusters for outliers, which often appear as clusters with only one member. Use a DATA step to delete outliers from the data set created by the OUTSEED= option before using it as a SEED= data set in later runs. If there are severe outliers, you should specify the STRICT option in the subsequent PROC FASTCLUS runs to prevent the outliers from distorting the clusters.

You can use the OUTSEED= data set with the SGPLOT procedure to plot `_GAP_`

by `_FREQ_`

. An overlay of `_RADIUS_`

by `_FREQ_`

provides a baseline against which to compare the values of `_GAP_`

. Outliers appear in the upper-left area of the plot, with large `_GAP_`

values and small `_FREQ_`

values. Good clusters appear in the upper-right area, with large values of both `_GAP_`

and `_FREQ_`

. Good potential cluster seeds appear in the lower right, as well as in the upper-right, since large `_FREQ_`

values indicate high-density regions. Small `_FREQ_`

values in the left part of the plot indicate poor cluster seeds because the points are in low-density regions. It often helps
to remove all clusters with small frequencies even though the clusters might not be remote enough to be considered outliers.
Removing points in low-density regions improves cluster separation and provides visually sharper cluster outlines in scatter
plots.