The data in this example, taken from Lee (1974), consist of patient characteristics and a variable indicating whether cancer remission occurred. This example demonstrates how to use PROC NLIN with a likelihood function. In this case, twice the negative of the loglikelihood function is to be minimized. This is the objective function for the analysis:
In this expression, denotes the success probability of the n Bernoulli trials, and is the log likelihood of n independent binary (Bernoulli) observations. The probability depends on the observations through the linear predictor ,
The linear predictor takes the form of a regression equation that is linear in the parameters,
Despite this linearity of in the z variables, the probit model is nonlinear, because the linear predictor appears inside the nonlinear probit function.
In order to use the NLIN procedure to minimize the function, the estimation problem must be cast in terms of a nonlinear least squares problem with objective function
This can be accomplished by setting and . Because , the function is strictly positive and the square root can be taken safely.
The following DATA step creates the data for the probit analysis. The variable like
is created in the DATA step, and it contains the value 0 throughout. This variable serves as the “dummy” response variable in the PROC NLIN step. The variable remiss
indicates whether cancer remission occurred. It is the binary outcome variable of interest and is used to determine the relevant
probability for observation i as the success or failure probability of a Bernoulli experiment.
data remiss; input remiss cell smear infil li blast temp; label remiss = 'complete remission'; like = 0; label like = 'dummy variable for nlin'; datalines; 1 0.8 .83 .66 1.9 1.10 .996 1 0.9 .36 .32 1.4 0.74 .992 0 0.8 .88 .70 0.8 0.176 .982 0 1 .87 .87 0.7 1.053 .986 1 0.9 .75 .68 1.3 0.519 .980 0 1 .65 .65 0.6 0.519 .982 1 0.95 .97 .92 1 1.23 .992 0 0.95 .87 .83 1.9 1.354 1.020 0 1 .45 .45 0.8 0.322 .999 0 0.95 .36 .34 0.5 0 1.038 0 0.85 .39 .33 0.7 0.279 .988 0 0.7 .76 .53 1.2 0.146 .982 0 0.8 .46 .37 0.4 0.38 1.006 0 0.2 .39 .08 0.8 0.114 .990 0 1 .90 .90 1.1 1.037 .990 1 1 .84 .84 1.9 2.064 1.020 0 0.65 .42 .27 0.5 0.114 1.014 0 1 .75 .75 1 1.322 1.004 0 0.5 .44 .22 0.6 0.114 .990 1 1 .63 .63 1.1 1.072 .986 0 1 .33 .33 0.4 0.176 1.010 0 0.9 .93 .84 0.6 1.591 1.020 1 1 .58 .58 1 0.531 1.002 0 0.95 .32 .30 1.6 0.886 .988 1 1 .60 .60 1.7 0.964 .990 1 1 .69 .69 0.9 0.398 .986 0 1 .73 .73 0.7 0.398 .986 ;
The following NLIN statements fit the probit model:
proc nlin data=remiss method=newton sigsq=1; parms int=10 a = 2 b = 1 c=6; linp = int + a*cell + b*li + c*temp; p = probnorm(linp); if (remiss = 1) then pi = 1p; else pi = p; model.like = sqrt( 2 * log(pi)); output out=p p=predict; run;
The assignment to the variable linp
creates the linear predictor of the generalized linear model,
In this example, the variables cell
, li
, and temp
are used as regressors.
By default, the NLIN procedure computes the covariance matrix of the parameter estimates based on the nonlinear least squares assumption. That is, the procedure computes the estimate of the residual variance as the mean squared error and uses that to multiply the inverse crossproduct matrix or the inverse Hessian matrix. (See the section Covariance Matrix of Parameter Estimates for details.) In the probit model, there is no residual variance. In addition, standard errors in maximum likelihood estimation are based on the inverse Hessian matrix. The METHOD=NEWTON option in the PROC NLIN statement is used to employ the Hessian matrix in computing the covariance matrix of the parameter estimates. The SIGSQ=1 option replaces the residual variance estimate that PROC NLIN would use by default as a multiplier of the inverse Hessian with the value 1.0.
Output 67.3.1 shows the results of this analysis. The analysis of variance table shows an apparently strange result. The total sum of squares is zero, and the model sum of squares is negative. Recall that the values of the response variable were set to zero and the mean function was constructed as in order for the NLIN procedure to minimize a loglikelihood function in terms of a nonlinear least squares problem. The value 21.9002 shown as the “Error” sum of squares is the value of the function .
Output 67.3.1: Nonlinear LeastSquares Analysis from PROC NLIN
Note:  An intercept was not specified for this model. 
Source  DF  Sum of Squares  Mean Square  F Value  Approx Pr > F 

Model  4  21.9002  5.4750  5.75  . 
Error  23  21.9002  0.9522  
Uncorrected Total  27  0 
Parameter  Estimate  Approx Std Error 
Approximate 95% Confidence Limits 


int  36.7548  32.3607  103.7  30.1885 
a  5.6298  4.6376  15.2235  3.9639 
b  2.2513  0.9790  4.2764  0.2262 
c  45.1815  34.9095  27.0343  117.4 
The problem can be more simply solved using dedicated procedures for generalized linear models:
proc glimmix data=remiss; model remiss = cell li temp / dist=binary link=probit s; run; proc genmod data=remiss; model remiss = cell li temp / dist=bin link=probit; run;
proc logistic data=remiss; model remiss = cell li temp / link=probit technique=newton; run;