The REG Procedure

Example 85.5 Ridge Regression for Acetylene Data

This example uses the acetylene data in Marquardt and Snee (1975) to illustrate the RIDGEPLOT and OUTVIF options. Here are the data:

data acetyl;
   input x1-x4 @@;
   x1x2 = x1 * x2;
   x1x1 = x1 * x1;
   label x1  = 'reactor temperature(celsius)'
         x2  = 'h2 to n-heptone ratio'
         x3  = 'contact time(sec)'
         x4  = 'conversion percentage'
         x1x2= 'temperature-ratio interaction'
         x1x1= 'squared temperature';
   datalines;
1300  7.5 .012 49   1300  9   .012  50.2 1300 11 .0115 50.5
1300 13.5 .013 48.5 1300 17   .0135 47.5 1300 23 .012  44.5
1200  5.3 .04  28   1200  7.5 .038  31.5 1200 11 .032  34.5
1200 13.5 .026 35   1200 17   .034  38   1200 23 .041  38.5
1100  5.3 .084 15   1100  7.5 .098  17   1100 11 .092  20.5
1100 17   .086 29.5
;
ods graphics on;

proc reg data=acetyl outvif
         outest=b ridge=0 to 0.02 by .002;
   model x4=x1 x2 x3 x1x2 x1x1;
run;
proc print data=b;
run;

When ODS Graphics is enabled and you request ridge regression by using the RIDGE= option in the PROC REG statement, PROC REG produces a panel showing variance inflation factors (VIF) in the upper plot in the panel and ridge traces in the lower plot. This panel is shown in Output 85.5.1.

Output 85.5.1: Ridge Regression and VIF Traces

Ridge Regression and VIF Traces


The OUTVIF option outputs the variance inflation factors to the OUTEST= data set that is shown in Output 85.5.2.

Output 85.5.2: OUTEST Data Set Showing VIF Values

Obs _MODEL_ _TYPE_ _DEPVAR_ _RIDGE_ _PCOMIT_ _RMSE_ Intercept x1 x2 x3 x1x2 x1x1 x4
1 MODEL1 PARMS x4 . . 1.15596 390.538 -0.78 10.174 -121.626 -0.008 0.00 -1
2 MODEL1 RIDGEVIF x4 0.000 . . . 7682.37 320.022 53.525 344.545 6643.32 -1
3 MODEL1 RIDGE x4 0.000 . 1.15596 390.538 -0.78 10.174 -121.626 -0.008 0.00 -1
4 MODEL1 RIDGEVIF x4 0.002 . . . 11.18 58.731 10.744 63.208 11.22 -1
5 MODEL1 RIDGE x4 0.002 . 2.69721 -103.388 0.05 4.404 -9.065 -0.003 0.00 -1
6 MODEL1 RIDGEVIF x4 0.004 . . . 4.36 23.939 9.996 25.744 5.15 -1
7 MODEL1 RIDGE x4 0.004 . 3.22340 -93.797 0.06 2.839 -21.338 -0.002 0.00 -1
8 MODEL1 RIDGEVIF x4 0.006 . . . 2.93 13.011 9.383 13.976 3.81 -1
9 MODEL1 RIDGE x4 0.006 . 3.47752 -87.687 0.06 2.110 -28.447 -0.001 0.00 -1
10 MODEL1 RIDGEVIF x4 0.008 . . . 2.36 8.224 8.838 8.821 3.23 -1
11 MODEL1 RIDGE x4 0.008 . 3.62677 -83.593 0.06 1.689 -33.377 -0.001 0.00 -1
12 MODEL1 RIDGEVIF x4 0.010 . . . 2.04 5.709 8.343 6.112 2.89 -1
13 MODEL1 RIDGE x4 0.010 . 3.72505 -80.603 0.06 1.414 -37.177 -0.001 0.00 -1
14 MODEL1 RIDGEVIF x4 0.012 . . . 1.84 4.226 7.891 4.514 2.65 -1
15 MODEL1 RIDGE x4 0.012 . 3.79477 -78.276 0.06 1.221 -40.297 -0.001 0.00 -1
16 MODEL1 RIDGEVIF x4 0.014 . . . 1.69 3.279 7.476 3.493 2.46 -1
17 MODEL1 RIDGE x4 0.014 . 3.84693 -76.381 0.06 1.078 -42.965 -0.001 0.00 -1
18 MODEL1 RIDGEVIF x4 0.016 . . . 1.57 2.637 7.094 2.801 2.31 -1
19 MODEL1 RIDGE x4 0.016 . 3.88750 -74.785 0.06 0.968 -45.309 -0.001 0.00 -1
20 MODEL1 RIDGEVIF x4 0.018 . . . 1.47 2.182 6.741 2.310 2.18 -1
21 MODEL1 RIDGE x4 0.018 . 3.92004 -73.407 0.06 0.880 -47.407 -0.000 0.00 -1
22 MODEL1 RIDGEVIF x4 0.020 . . . 1.39 1.847 6.415 1.949 2.06 -1
23 MODEL1 RIDGE x4 0.020 . 3.94679 -72.193 0.06 0.809 -49.310 -0.000 0.00 -1



If you want to obtain separate plots containing the ridge traces and VIF traces, you can specify the UNPACK suboption in the PLOTS=RIDGE option. You can also request that one or both of the VIF axis and ridge parameter axis be displayed on a logarithmic scale. You can see in Output 85.5.1 that the VIF traces for several of the parameters are nearly indistinguishable when displayed on a linear scale. The following code illustrates how you obtain separate VIF and ridge traces with the VIF values displayed on a logarithmic scale. Note that you can obtain plots of VIF values even though you do not specify the OUTVIF option in the PROC REG statement.

proc reg data=acetyl plots(only)=ridge(unpack VIFaxis=log)
         outest=b ridge=0 to 0.02 by .002;
   model x4=x1 x2 x3 x1x2 x1x1;
run;

ods graphics off;

The requested plots are shown in Output 85.5.3 and Output 85.5.4.

Output 85.5.3: VIF Traces

VIF Traces


Output 85.5.4: Ridge Traces

Ridge Traces