The Quadratic Programming Solver

Getting Started: QP Solver

Consider a small illustrative example. Suppose you want to minimize a two-variable quadratic function $f(x_1, x_2)$ on the nonnegative quadrant, subject to two constraints:

$\begin{array}{rccccccccl} \min & 2x_1 & + & 3x_2 & + & x_1^2 & + & 10x_2^2 & + & 2.5 x_1 x_2 \\ \mbox{subject to} & x_1 & - & x_2 & \le & 1 & & & & \\ & x_1 & + & 2x_2 & \ge & 100 & & & & \\ & x_1 & & & \ge & 0 & & & & \\ & & & x_2 & \ge & 0 & & & & \end{array}$

To use the OPTMODEL procedure, it is not necessary to fit this problem into the general QP formulation mentioned in the section Overview: QP Solver and to compute the corresponding parameters. However, since these parameters are closely related to the data set that is used by the OPTQP procedure and has a quadratic programming system (QPS) format, you can compute these parameters as follows. The linear objective function coefficients, vector of right-hand sides, and lower and upper bounds are identified immediately as

$\mathbf{c} = \left[\begin{array}{c} 2 \\ 3 \end{array}\right],\quad \mathbf{b} = \left[\begin{array}{c} 1 \\ 100 \end{array}\right],\quad \mathbf{l} = \left[\begin{array}{c} 0 \\ 0 \end{array}\right],\quad \mathbf{u} = \left[\begin{array}{c} +\infty \\ +\infty \end{array}\right]$

Carefully construct the quadratic matrix $\mathbf{Q}$ . Observe that you can use symmetry to separate the main-diagonal and off-diagonal elements:

$\frac{1}{2} \mathbf{x}^\textrm {T} \mathbf{Qx} \equiv \frac{1}{2} \sum _{i, j = 1}^ n\; x_ i\, q_{ij}\, x_ j = \frac{1}{2} \sum _{i = 1}^ n\; q_{ii}\, x_ i^2 + \sum _{i > j}\; x_ i\, q_{ij}\, x_ j$

The first expression

$\frac{1}{2} \sum _{i = 1}^{n}\; q_{ii}\, x_ i^2$

sums the main-diagonal elements. Thus, in this case you have

$q_{11} = 2,\quad q_{22} = 20$

Notice that the main-diagonal values are doubled in order to accommodate the 1/2 factor. Now the second term

$\sum _{i > j} x_ i\, q_{ij}\, x_ j$

sums the off-diagonal elements in the strict lower triangular part of the matrix. The only off-diagonal ( $x_ i\, x_ j,\; i\not=j$ ) term in the objective function is $2.5\, x_1\, x_2$ , so you have

$q_{21} = 2.5$

Notice that you do not need to specify the upper triangular part of the quadratic matrix.

Finally, the matrix of constraints is as follows:

$\mathbf{A} = \left[\begin{array}{cr} 1 & -1 \\ 1 & 2 \end{array}\right]$

The following OPTMODEL program formulates the preceding problem in a manner that is very close to the mathematical specification of the given problem:

/* getting started */
proc optmodel;
   var x1 >= 0; /* declare nonnegative variable x1 */
   var x2 >= 0; /* declare nonnegative variable x2 */

   /* objective: quadratic function f(x1, x2) */
   minimize f =
       /* the linear objective function coefficients */
       2 * x1 + 3 * x2 +

       /* quadratic <x, Qx> */
       x1 * x1 + 2.5 * x1 * x2 + 10 * x2 * x2;

   /* subject to the following constraints */
   con r1: x1 - x2 <= 1;
   con r2: x1 + 2 * x2 >= 100;

   /* specify iterative interior point algorithm (QP)
    * in the SOLVE statement */
   solve with qp;

   /* print the optimal solution */
   print x1 x2;
   save qps qpsdata;
quit;

The "with qp" clause in the SOLVE statement invokes the QP solver to solve the problem. The output is shown in Figure 11.2.

Figure 11.2: Summaries and Optimal Solution

The OPTMODEL Procedure

Problem Summary
Objective Sense	Minimization
Objective Function	f
Objective Type	Quadratic

Number of Variables	2
Bounded Above	0
Bounded Below	2
Bounded Below and Above	0
Free	0
Fixed	0

Number of Constraints	2
Linear LE (<=)	1
Linear EQ (=)	0
Linear GE (>=)	1
Linear Range	0

Constraint Coefficients	4

Performance Information
Execution Mode	Single-Machine
Number of Threads	4

Solution Summary
Solver	QP
Algorithm	Interior Point
Objective Function	f
Solution Status	Optimal
Objective Value	15018

Primal Infeasibility	0
Dual Infeasibility	0
Bound Infeasibility	0
Duality Gap	3.633377E-16
Complementarity	0

Iterations	6
Presolve Time	0.00
Solution Time	0.03

x1	x2
34	33

In this example, the SAVE QPS statement is used to save the QP problem in the QPS-format data set qpsdata, shown in Figure 11.3. The data set is consistent with the parameters of general quadratic programming previously computed. Also, the data set can be used as input to the OPTQP procedure.

Figure 11.3: QPS-Format Data Set

Obs	FIELD1	FIELD2	FIELD3	FIELD4	FIELD5	FIELD6
1	NAME		qpsdata	.		.
2	ROWS			.		.
3	N	f		.		.
4	L	r1		.		.
5	G	r2		.		.
6	COLUMNS			.		.
7		x1	f	2.0	r1	1
8		x1	r2	1.0		.
9		x2	f	3.0	r1	-1
10		x2	r2	2.0		.
11	RHS			.		.
12		.RHS.	r1	1.0		.
13		.RHS.	r2	100.0		.
14	QSECTION			.		.
15		x1	x1	2.0		.
16		x1	x2	2.5		.
17		x2	x2	20.0		.
18	ENDATA			.		.