SUPPORT / SAMPLES & SAS NOTES
Usage Note 33579: Signing on or off to a host with SAS/CONNECT® software might fail after about 200 successful attempts
 |  |  |  |  |
The following error might occur, even after you have signed on or off with SAS/CONNECT software with about 200 successful attempts:
ERROR: A communication subsystem partner link setup request failure has
occurred.
ERROR: TCP link establishment failed.
ERROR: Remote signon to HOST.XXXX canceled.
If you include the –VERBOSE option to the spawner, you can see the following traceback information in the spawner log:
SAS Job Spawner for Open Systems version 9.2
%SYSTEM-F-ACCVIO, access violation, reason mask=04, virtual address=000000000115
C868, PC=00000000000DDD41, PS=0000001B
%TRACE-F-TRACEBACK, symbolic stack dump follows
image module routine line rel PC abs PC
Error: malloc failed for 0x00000000.000cca5b bytes for section 0x03 contents
tkmk skmlink skm_unlinke 0 0000000000000BB1 00000000000DDD41
Error: malloc failed for 0x00000000.000cca5b bytes for section 0x03 contents
tkmk skmprlse skmMemRelease 0 00000000000005C0 00000000000D9290
tkitcp skstsock tkstSockDestroy 61378 0000000000001840 0000000001129B90
sastcpd daemon spexit 96490 0000000000017200 0000000000047200
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_UPCALLS upcAstDelivery
0 00000000000008E0 FFFFFFFF8456B6D0
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_UPCALLS upcAstForThread
0 0000000000000C20 FFFFFFFF8456BA10
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_UPCALLS upcCallInterrupts
0 00000000000025C0 FFFFFFFF8456D3B0
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_DISPATCH dspDispatchEndGame
0 0000000000001710 FFFFFFFF84511A90
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_DISPATCH dspDispatch
0 0000000000000F90 FFFFFFFF84511310
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_COND cvWaitPrim 0 0000000000008560 FFFFFFFF84509710
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_COND pthread_cond_wait
0 00000000000034B0 FFFFFFFF84504660
Error: malloc failed for 0x00000000.000cca5b bytes for section 0x03 contents
tkmk TKPOSbktWait bktWait 0 00000000000002F0 00000000000C9670
Error: malloc failed for 0x00000000.000cca5b bytes for section 0x03 contents
tkmk sktWait sktWait 0 0000000000000390 00000000000C6E40
sastcpd tkwait tkWait 34709 0000000000000120 0000000000062300
sastcpd daemon main 92547 0000000000000890 0000000000030890
sastcpd daemon __main 92436 00000000000002D0 00000000000302D0
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_THREAD thdBase 0 0000000000005BF0 FFFFFFFF84543290
Error: malloc failed for 0x00000000.00071a9a bytes for section 0x03 contents
PTHREAD$RTL THD_INIT pthread_main 0 00000000000006C0 FFFFFFFF844FA6C0
0 FFFFFFFF80B8E820 FFFFFFFF80B8E820
DCL 0 000000000006BA90 000000007ADE3A90
%TRACE-I-END, end of TRACE stack dump
This problem occurs because the quota for the spawner program (sastcpd) page file is too low.
The only workaround at this time is to restart the spawner or consult your system administrator about increasing the page-file quota on your operating system to enable the spawner to run longer between restart times.
Operating System and Release Information
| Product Family | Product | System | SAS Release | |
| Reported | Fixed* | |||
| SAS System | SAS/CONNECT | OpenVMS on HP Integrity | 9.2 TS1M0 | |