The MIANALYZE Procedure

Example 64.11 Combining Correlation Coefficients

This example combines sample correlation coefficients that are computed from a set of imputed data sets by using Fisher’s z transformation.

Fisher’s z transformation of the sample correlation r is

\[  z = \frac{1}{2} \,  \mr{log} \left( \frac{1+r}{1-r} \right)  \]

The statistic z is approximately normally distributed, with mean

\[  \mr{log} \left( \frac{1+\rho }{1-\rho } \right)  \]

and variance $1/(n-3)$, where $\rho $ is the population correlation coefficient and n is the number of observations.

The following statements use the CORR procedure to compute the correlation r and its associated Fisher’s z statistic between the variables Oxygen and RunTime for each imputed data set. The ODS statement is used to save Fisher’s z statistic in an output data set.

proc corr data=outmi fisher(biasadj=no);
   var Oxygen RunTime;
   by _Imputation_;
   ods output FisherPearsonCorr= outz;
run;

The following statements display the number of observations and Fisher’s z statistic for each imputed data set in Output 64.11.1:

proc print data=outz;
   title 'Fisher''s Correlation Statistics';
   var _Imputation_ NObs ZVal;
run;

Output 64.11.1: Output z Statistics

Fisher's Correlation Statistics

Obs _Imputation_ NObs ZVal
1 1 31 -1.27869
2 2 31 -1.30715
3 3 31 -1.27922
4 4 31 -1.39243
5 5 31 -1.40146



The following statements generate the standard error associated with the z statistic, $1/\sqrt {n-3}$:

data outz;
   set outz;
   StdZ= 1. / sqrt(NObs-3);
run;

The following statements use the MIANALYZE procedure to generate a combined parameter estimate $\hat{z}$ and its variance, as shown in Output 64.11.2. The ODS statement is used to save the parameter estimates in an output data set.

proc mianalyze data=outz;
   ods output ParameterEstimates=parms;
   modeleffects ZVal;
   stderr StdZ;
run;

Output 64.11.2: Combining Fisher’s z Statistics

The MIANALYZE Procedure

Parameter Estimates
Parameter Estimate Std Error 95% Confidence Limits DF Minimum Maximum Theta0 t for H0:
Parameter=Theta0
Pr > |t|
ZVal -1.331787 0.200327 -1.72587 -0.93771 330.23 -1.401459 -1.278686 0 -6.65 <.0001



In addition to the estimate for z, PROC MIANALYZE also generates 95% confidence limits for z, $\hat{z}_{.025}$ and $\hat{z}_{.975}$. The following statements print the estimate and 95% confidence limits for z in Output 64.11.3:

proc print data=parms;
   title 'Parameter Estimates with 95% Confidence Limits';
   var Estimate LCLMean UCLMean;
run;

Output 64.11.3: Parameter Estimates with 95% Confidence Limits

Parameter Estimates with 95% Confidence Limits

Obs Estimate LCLMean UCLMean
1 -1.331787 -1.72587 -0.93771



An estimate of the correlation coefficient with its corresponding 95% confidence limits is then generated from the following inverse transformation as described in the section Correlation Coefficients:

\[  r = \mr{tanh}(z) =\frac{e^{2z} - 1}{e^{2z} + 1}  \]

for $z = \hat{z}$, $\hat{z}_{.025}$, and $\hat{z}_{.975}$.

The following statements generate and display an estimate of the correlation coefficient and its 95% confidence limits, as shown in Output 64.11.4:

data corr_ci;
   set parms;
   r=       tanh( Estimate);
   r_lower= tanh( LCLMean);
   r_upper= tanh( UCLMean);
run;
proc print data=corr_ci;
   title 'Estimated Correlation Coefficient'
         ' with 95% Confidence Limits';
   var r r_lower r_upper;
run;

Output 64.11.4: Estimated Correlation Coefficient

Estimated Correlation Coefficient with 95% Confidence Limits

Obs r r_lower r_upper
1 -0.86969 -0.93857 -0.73417