Previous Page

|

Next Page

The SEQDESIGN Procedure

Example 77.10 Creating Two-Sided Error Spending Designs with and without Overlapping Lower and Upper Boundaries

This example requests two three-stage group sequential designs for normally distributed statistics. Each design uses a power family error spending function with a specified two-sided alternative hypothesis and early stopping only to accept the null hypothesis .

The first design uses the BETAOVERLAP=NOADJUST option to derive acceptance boundary values without adjusting for the possible overlapping of the lower and upper boundaries computed from the two corresponding one-sided tests. The second design uses the BETAOVERLAP=ADJUST option to test the overlapping of the boundaries at each interim stage based on the two corresponding one-sided tests and then to set the boundary values at the stage to missing if overlapping occurs at that stage.

The following statements request a two-sided design with the BETAOVERLAP=NOADJUST option:

   ods graphics on;
   proc seqdesign altref=0.2 errspend;
      design nstages=3
             method=errfuncpow
             alt=twosided  stop=accept
             betaoverlap=noadjust
             beta=0.09
             ;
   run;
   ods graphics off;

The "Design Information" table in Output 77.10.1 displays design specifications and the derived statistics for the first design. With the specified alternative reference , the maximum information is derived.

Output 77.10.1 Design Information

The SEQDESIGN Procedure

Design: Design_1

Design Information
Statistic Distribution	Normal
Boundary Scale	Standardized Z
Alternative Hypothesis	Two-Sided
Early Stop	Accept Null
Method	Error Spending
Boundary Key	Both
Alternative Reference	0.2
Number of Stages	3
Alpha	0.05
Beta	0.09
Power	0.91
Max Information (Percent of Fixed Sample)	103.8789
Max Information	282.9328
Null Ref ASN (Percent of Fixed Sample)	79.20197
Alt Ref ASN (Percent of Fixed Sample)	102.1476

The "Boundary Information" table in Output 77.10.2 displays the information level, alternative reference, and boundary values. With a specified alternative reference , the maximum information is derived from the procedure, and the actual information level at each stage is displayed in the table. With the default BOUNDARYSCALE=STDZ option, the alternative reference in the standardized scale at stage is given by , where is the specified alternative reference and is the information level at stage , .

The "Error Spending Information" table in Output 77.10.3 displays the cumulative error spending at each stage for each boundary.

With the STOP=ACCEPT option, the design does not stop at interim stages to reject , and the spending at each interim stage is zero. For the power family error spending function with the default parameter , the beta spending at stage is , and the cumulative beta spending at stage is .

With the specified ODS GRAPHICS ON statement, a detailed boundary plot with the acceptance and rejection regions is displayed by default, as shown in Output 77.10.4.

Output 77.10.4 Boundary Plot

The following statements request a two-sided design with the BETAOVERLAP=ADJUST option, which is the default:

   ods graphics on;
   proc seqdesign altref=0.2 errspend;
      design nstages=3
             method=errfuncpow
             alt=twosided 
             stop=accept
             betaoverlap=adjust
             beta=0.09
             ;
   run;
   ods graphics off;

With the BETAOVERLAP=ADJUST option, the procedure first derives the usual boundary values for the two-sided design and then checks for overlapping of the boundaries for the two corresponding one-sided tests at each stage. If this type of overlapping occurs at a particular stage, the boundary values for that stage are set to missing, the spending values at that stage are reset to zero, and the spending values at subsequent stages are adjusted proportionally.

The boundary values without adjusting for the possible overlapping of the two one-sided boundaries are identical to the boundary values derived in the first design (with the BETAOVERLAP=NOADJUST option, as shown in Output 77.10.2). At stage , the upper boundary value for the corresponding one-sided test is

where is the upper alternative reference, is the information level at stage , and is the spending at stage (as shown in Output 77.10.3).

Similarly, the lower boundary value for the corresponding one-sided test is computed as . Since the upper boundary value is less than the lower boundary at stage , overlapping occurs, and so the boundary values for the two-sided design are set to missing at stage .

With the boundary values set to missing at stage and the spending the spending values at subsequent interim stages are adjusted proportionally. In this example, the adjusted spending at stage is computed as

where is the cumulative spending at stage before the adjustment, .

The "Design Information" table in Output 77.10.5 displays design specifications and derived statistics for the design.

The "Boundary Information" table in Output 77.10.6 displays the information levels, alternative references, and boundary values.

The "Error Spending Information" table in Output 77.10.7 displays the cumulative error spending at each stage for each boundary.

With the specified ODS GRAPHICS ON statement, a detailed boundary plot with the acceptance and rejection regions is displayed by default, as shown in Output 77.10.8.

Output 77.10.8 Boundary Plot

Copyright © 2009 by SAS Institute Inc., Cary, NC, USA. All rights reserved.