writes the parameter estimate covariance matrix to the OUTEST= data set.

controls how the natural response is handled. Specify the OPTC option to request that the natural response rate be estimated. Specify the C=rate option to set the natural response rate or to provide the initial estimate of the natural response rate. The natural response rate value must be a number between 0 and 1.

• If you specify neither the OPTC nor the C= option, a natural response rate of zero is assumed.

• If you specify both the OPTC and the C= option, the C= option should be a reasonable initial estimate of the natural response rate. For example, you could use the ratio of the number of responses to the number of subjects in a control group.

• If you specify the C= option but not the OPTC option, the natural response rate is set to the specified value and not estimated.

• If you specify the OPTC option but not the C= option, PROC PROBIT’s action depends on the response variable, as follows:

  • If you specify either the LN or LOG10 option and some subjects have the first independent variable (dose) values less than or equal to zero, these subjects are treated as a control group. The initial estimate of is then the ratio of the number of responses to the number of subjects in this group.

  • If you do not specify the LN or LOG10 option or if there is no control group, then one of the following occurs:

    • If all responses are greater than zero, the initial estimate of the natural response rate is the minimal response rate (the ratio of the number of responses to the number of subjects in a dose group) across all dose levels.

    • If one or more of the responses is zero (making the response rate zero in that dose group), the initial estimate of the natural rate is the reciprocal of twice the largest number of subjects in any dose group in the experiment.

specifies the SAS data set to be used by PROC PROBIT. By default, the procedure uses the most recently created SAS data set.

specifies a graphics catalog in which to save graphics output.

specifies a minimum probability level for the Pearson chi-square to indicate a good fit. The default value is 0.10. The LACKFIT option must also be specified for this option to have any effect. For Pearson goodness-of-fit chi-square values with probability greater than the HPROB= value, the fiducial limits, if requested with the INVERSECL option, are computed by using a critical value of 1.96. For chi-square values with probability less than the value of the HPROB= option, the critical value is a 0.95 two-sided quantile value taken from the distribution with degrees of freedom equal to , where is the number of levels for the response variable, is the number of different sets of independent variable values, and is the number of parameters fit in the model. Note that the HPROB= option can also appear in the MODEL statement.

specifies an input SAS data set that contains initial estimates for all the parameters in the model. See the section INEST= SAS-data-set for a detailed description of the contents of the INEST= data set.

computes confidence limits for the values of the first continuous independent variable (such as dose) that yield selected response rates. If the algorithm fails to converge (this can happen when is nonzero), missing values are reported for the confidence limits. See the section Inverse Confidence Limits for details. Note that the INVERSECL option can also appear in the MODEL statement.

performs two goodness-of-fit tests (a Pearson chi-square test and a log-likelihood ratio chi-square test) for the fitted model.

To compute the test statistics, proper grouping of the observations into subpopulations is needed. You can use the AGGREGATE or AGGREGATE= option for this end. See the entry for the AGGREGATE and AGGREGATE= options under the MODEL statement. If neither AGGREGATE nor AGGREGATE= is specified, PROC PROBIT assumes each observation is from a separate subpopulation and computes the goodness-of-fit test statistics only for the events/trials syntax.

Note:This test is not appropriate if the data are very sparse, with only a few values at each set of the independent variable values.

If the Pearson chi-square test statistic is significant, then the covariance estimates and standard error estimates are adjusted. See the section Lack-of-Fit Tests for a description of the tests. Note that the LACKFIT option can also appear in the MODEL statement.

analyzes the data by replacing the first continuous independent variable with its natural logarithm. This variable is usually the level of some treatment such as dosage. In addition to the usual output given by the INVERSECL option, the estimated dose values and 95% fiducial limits for dose are also displayed. If you specify the OPTC option, any observations with a dose value less than or equal to zero are used in the estimation as a control group. If you do not specify the OPTC option with the LOG or LN option, then any observations with the first continuous independent variable values less than or equal to zero are ignored.

specifies an analysis like that of the LN or LOG option, except that the common logarithm (log to the base 10) of the dose value is used rather than the natural logarithm.

specifies the length of effect names in tables and output data sets to be characters, where is a value between 20 and 200. The default length is 20 characters.

suppresses the display of all output including graphics. Note that this option temporarily disables the Output Delivery System (ODS). For more information, see Chapter 20, Using the Output Delivery System.

controls how the natural response is handled. See the description of the C= option on for details.

specifies the sorting order for the levels of the classification variables specified in the CLASS statement, including the levels of the response variable. Response level ordering is important since PROC PROBIT always models the probability of response levels at the beginning of the ordering. See the section Response Level Ordering for further details. This ordering also determines which parameters in the model correspond to each level in the data. The following table shows how PROC PROBIT interprets values of the ORDER= option.

By default, ORDER=FORMATTED. For the values FORMATTED and INTERNAL, the sort order is machine dependent. For more information about sorting order, see the chapter on the SORT procedure in the Base SAS Procedures Guide.

specifies a SAS data set to contain the parameter estimates and, if the COVOUT option is specified, their estimated covariances. If you omit this option, the output data set is not created. The contents of the data set are described in the section OUTEST= SAS-data-set.

specifies options that control details of the plots created by ODS Graphics. These plots are related to a dose variable, which is identified as the first single continuous independent variable in the MODEL statement. If there are interaction terms with this variable in the model, the PROBIT procedure will not produce any plot.

You can specify more than one plot request within the parentheses after PLOTS=. For a single plot request, you can omit the parentheses. The following plot requests are available.

specifies an input SAS data set that contains values for all the independent variables in the MODEL statement and variables in the CLASS statement. If there are covariates specified in a MODEL statement, you specify fixed values for the effects in the MODEL statement by the XDATA= data set when predicted values and/or fiducial limits for a single continuous variable (dose variable) are required. These specified values for the effects in the MODEL statement are also used for generating plots. See the section XDATA= SAS-data-set for a detailed description of the contents of the XDATA= data set.