Previous Page | Next Page

The VARMAX Procedure

OUT= Data Set

The OUT= data set contains the forecast values produced by the OUTPUT statement. The following output variables can be created:

  • the BY variables

  • the ID variable

  • the MODEL statement dependent (endogenous) variables. These variables contain the actual values from the input data set.

  • FORi, numeric variables that contain the forecasts. The FORi variables contain the forecasts for the ith endogenous variable in the MODEL statement list. Forecasts are one-step-ahead predictions until the end of the data or until the observation specified by the BACK= option. Multistep forecasts can be computed after that point based on the LEAD= option.

  • RESi, numeric variables that contain the residual for the forecast of the ith endogenous variable in the MODEL statement list. For multistep forecast observations, the actual values are missing and the RESi variables contain missing values.

  • STDi, numeric variables that contain the standard deviation for the forecast of the ith endogenous variable in the MODEL statement list. The values of the STDi variables can be used to construct univariate confidence limits for the corresponding forecasts.

  • LCIi, numeric variables that contain the lower confidence limits for the corresponding forecasts of the ith endogenous variable in the MODEL statement list.

  • UCIi, numeric variables that contain the upper confidence limits for the corresponding forecasts of the ith endogenous variable in the MODEL statement list.

The OUT= data set contains the values shown in Table 30.3 and Table 30.4 for a bivariate case.

Table 30.3 OUT= Data Set

Obs

ID variable

y1

FOR1

RES1

STD1

LCI1

UCI1

1

date

2

date

             
Table 30.4 OUT= Data Set Continued

Obs

y2

FOR2

RES2

STD2

LCI2

UCI2

1

2

           

Consider the following example:

   proc varmax data=simul1 noprint;
      id date interval=year;
      model y1 y2 / p=1 noint;
      output out=out lead=5;
   run;
   proc print data=out(firstobs=98);
   run;

The output in Figure 30.66 shows part of the results of the OUT= data set for the preceding example.

Figure 30.66 OUT= Data Set
Obs date y1 FOR1 RES1 STD1 LCI1 UCI1 y2 FOR2 RES2 STD2 LCI2 UCI2
98 1997 -0.58433 -0.13500 -0.44934 1.13523 -2.36001 2.09002 0.64397 -0.34932 0.99329 1.19096 -2.68357 1.98492
99 1998 -2.07170 -1.00649 -1.06522 1.13523 -3.23150 1.21853 0.35925 -0.07132 0.43057 1.19096 -2.40557 2.26292
100 1999 -3.38342 -2.58612 -0.79730 1.13523 -4.81113 -0.36111 -0.64999 -0.99354 0.34355 1.19096 -3.32779 1.34070
101 2000 . -3.59212 . 1.13523 -5.81713 -1.36711 . -2.09873 . 1.19096 -4.43298 0.23551
102 2001 . -3.09448 . 1.70915 -6.44435 0.25539 . -2.77050 . 1.47666 -5.66469 0.12369
103 2002 . -2.17433 . 2.14472 -6.37792 2.02925 . -2.75724 . 1.74212 -6.17173 0.65725
104 2003 . -1.11395 . 2.43166 -5.87992 3.65203 . -2.24943 . 2.01925 -6.20709 1.70823
105 2004 . -0.14342 . 2.58740 -5.21463 4.92779 . -1.47460 . 2.25169 -5.88782 2.93863

Previous Page | Next Page | Top of Page