The MDC Procedure


NEST Statement

  • NEST LEVEL ( level-number )= ( choices@choice, …);

The NEST statement is used when one choice variable contains all possible alternatives and the TYPE=NLOGIT option is specified. The decision tree is constructed based on the NEST statement. When the choice set is specified using multiple CHOICE= variables in the MODEL statement, the NEST statement is ignored.

Consider the following eight choices that are nested in a three-level tree structure.

   Level 1     Level 2     Level 3    top
      1           1           1        1
      2           1           1        1
      3           1           1        1
      4           2           1        1
      5           2           1        1
      6           2           1        1
      7           3           2        1
      8           3           2        1

You can use the following NEST statement to specify the tree structure displayed in Figure 18.22:

   nest level(1) = (1 2 3 @ 1, 4 5 6 @ 2, 7 8 @ 3),
        level(2) = (1 2 @ 1, 3 @ 2),
        level(3) = (1 2 @ 1);

Figure 18.22: A Three-Level Tree

A Three-Level Tree


Note that the decision tree is constructed based on the sequence of first-level choice set specification. Therefore, specifying another order at Level 1 builds a different tree. The following NEST statement builds the tree displayed in Figure 18.23:

   nest level(1) = (4 5 6 @ 2, 1 2 3 @ 1, 7 8 @ 3),
        level(2) = (1 2 @ 1, 3 @ 2),
        level(3) = (1 2 @ 1);

Figure 18.23: An Alternative Three-Level Tree

An Alternative Three-Level Tree


However, the NEST statement with a different sequence of choice specification at higher levels builds the same tree as displayed in Figure 18.22 if the sequence at the first level is the same:

   nest level(1) = (1 2 3 @ 1, 4 5 6 @ 2, 7 8 @ 3),
        level(2) = (3 @ 2, 1 2 @ 1),
        level(3) = (1 2 @ 1);

The following specifications are equivalent:

   nest level(2) = (3 @ 2, 1 2 @ 1)

   nest level(2) = (3 @ 2, 1 @ 1, 2 @ 1)

   nest level(2) = (1 @ 1, 2 @ 1, 3 @ 2)

Since the MDC procedure contains multiple cases for each individual, it is important to keep the data sequence in the proper order. Consider the four-choice multinomial model with one explanatory variable cost:

   pid   choice  y   cost
    1      1     1    10
    1      2     0    25
    1      3     0    20
    1      4     0    30
    2      1     0    15
    2      2     0    22
    2      3     1    16
    2      4     0    25

The order of data needs to correspond to the value of choice. Therefore, the following data set is equivalent to the preceding data:

   pid   choice  y   cost
    1      2     0    25
    1      3     0    20
    1      1     1    10
    1      4     0    30
    2      3     1    16
    2      4     0    25
    2      1     0    15
    2      2     0    22

The two-level nested model is estimated with a NEST statement, as follows:

   proc mdc data=one type=nlogit;
      model y = cost / choice=(choice);
      id pid;
      utility(1,) = cost;
      nest level(1) = (1 2 3 @ 1, 4 @ 2),
           level(2) = (1 2 @ 1);
   run;

The tree is constructed as in Figure 18.24.

Figure 18.24: A Two-Level Tree

A Two-Level Tree


Another model is estimated if you specify the decision tree as in Figure 18.25. The different nested tree structure is specified in the following SAS statements:

   proc mdc data=one type=nlogit;
      model y = cost / choice=(choice);
      id pid;
      utility u(1,) = cost;
      nest level(1) = (1 @ 1, 2 3 4 @ 2),
           level(2) = (1 2 @ 1);
   run;

Figure 18.25: An Alternate Two-Level Tree

An Alternate Two-Level Tree